Updated Nov 18, 2026· 6 min read

Key takeaways

  • A 200 amp 5-jaw meter socket is the right part for a residential or light-commercial service upgrade where the utility company requires a five-jaw meter…

A 200 amp 5-jaw meter socket is the right part for a residential or light-commercial service upgrade where the utility company requires a five-jaw meter base rather than the more common four-jaw type, and the specific model you need depends on your utility’s exact requirements, local electrical code, and whether you need a plain meter socket or one combined with a main breaker or bypass lever. This is work for a licensed electrician in almost every jurisdiction, both because utilities typically require it and because mistakes at the service entrance carry a real risk of serious injury.

What Makes a Meter Socket “5-Jaw”

The jaw count on a meter socket refers to the number of contact clips inside the base that grip the prongs on the utility meter itself. A standard residential meter typically uses a four-jaw base with two line-side and two load-side contacts, while a five-jaw base adds a fifth contact position, most often used for utilities that require a connection for load management, demand response equipment, or certain net-metering and solar interconnection setups. Utilities specify the required jaw count, not homeowners, so the first step before buying is confirming with your local utility exactly what configuration they require for your service.

Why the Utility’s Requirement Comes First

Meter sockets are typically supplied or approved by the utility, or at minimum must match a utility-published list of approved models for a given service area, because the utility owns and reads the meter that plugs into the socket. Installing a meter socket that doesn’t match your utility’s approved configuration can result in a failed inspection, a required re-do, or a refusal to energize the service, so confirming compatibility before purchase avoids wasted cost and delay.

At a Glance: 200A 5-Jaw Meter Socket Types

Type / Example Brand Lines Best For Key Stated Specs Limits
Plain ringless 5-jaw meter sockets (e.g., Milbank, Eaton, Siemens lines) Straightforward service upgrades with no combined breaker The maker lists 200A rating, five-jaw configuration, ringless cover design Requires a separate main breaker enclosure elsewhere in the service; check utility ring-type vs ringless requirements
Ring-type 5-jaw meter sockets Utility areas that specifically require a sealing ring cover The maker lists 200A rating with a ring-style meter cover for utility seal Not interchangeable with ringless requirements; confirm which type your utility mandates
Meter socket with integrated main breaker (meter-main combo) Service upgrades combining the meter base and main disconnect in one enclosure The maker lists 200A rated main breaker built into a 5-jaw meter socket enclosure Larger enclosure footprint; local code may dictate where the main disconnect must be located relative to the meter
Meter socket with bypass lever Utilities that require the ability to bypass the meter for maintenance without de-energizing the whole service The maker lists a manual bypass lever rated for 200A alongside the five-jaw base Added mechanical complexity; bypass lever operation should only be used per utility/electrician instruction

What to Check Before Buying

Confirm the amperage rating matches your actual service size; a 200A-rated socket is built and UL-listed specifically for that load class, and using an under-rated enclosure on a 200A service is a code violation and a fire-safety risk. Check the enclosure’s listing marks (UL or CSA, depending on your country) and confirm it’s rated for your installation environment, such as outdoor/rainproof-rated if it will be mounted outside, which is the typical case for residential service equipment. Horizontal vs. vertical conduit entry, overhead vs. underground service compatibility, and the specific utility’s approved-equipment list are all details worth confirming with your electrician or utility before purchase, since these vary by region and even by specific utility company within the same state or province.

Permits and Utility Coordination

A 200A service upgrade almost always requires a permit, an inspection, and coordination with the utility to schedule a temporary disconnect and reconnect. This is standard practice everywhere licensed electrical work is regulated, and skipping these steps can leave a homeowner without insurance coverage in the event of a fire, in addition to being against code. Follow your local utility’s and electrician’s guidance on timing and process rather than attempting to swap a live meter socket yourself.

Pick This If…

Your Situation Suggested Choice
Your utility specifies a plain ringless 5-jaw base A ringless 200A 5-jaw meter socket matching their approved list
Your utility requires a sealing ring on the meter cover A ring-type 200A 5-jaw meter socket
You’re combining the meter base and main disconnect in one location A meter-main combo unit rated for 200A with 5-jaw configuration
Your utility requires bypass capability for meter servicing A 5-jaw socket with an integrated, utility-approved bypass lever
You’re unsure which configuration applies to your address Contact your utility’s new-service or metering department before buying anything

Fit and Compatibility Notes

Conduit entry location, enclosure depth, and mounting hole pattern all need to match your existing service panel layout and wall structure, which is why this is normally specified by the electrician doing the work rather than chosen independently off a spec sheet. If this is a replacement for a damaged or outdated meter socket rather than a new service, bring the old unit’s model number and utility account information to your electrician or supplier, since matching the existing utility seal and jaw configuration avoids an unnecessary dispute with the utility at reconnection time.

Alternatives Worth Considering

4-Jaw Meter Sockets

The more common configuration for standard residential service without special utility requirements; only relevant if your utility confirms a four-jaw base is acceptable for your situation.

Meter Socket with Transfer Switch Provisions

For homeowners planning a backup generator connection, some meter-adjacent equipment includes provisions for a transfer switch; this is a separate decision from jaw count and should be planned with your electrician as part of the same service upgrade if relevant.

Full Service Panel Replacement Kits

If the meter socket swap is part of a larger panel upgrade, some manufacturers sell combined kits bundling the meter socket, main panel, and breakers, which can simplify sourcing matched, code-compliant components for the whole job.

Frequently Asked Questions

Can I install a 200 amp 5-jaw meter socket myself?

In almost every jurisdiction this work must be done by a licensed electrician, and utilities typically will not energize a meter installed without a permit and inspection. Attempting this work without training carries a serious risk of electrocution or fire, since the service conductors feeding the meter base are energized directly from the utility.

How do I know if my utility needs a 4-jaw or 5-jaw meter socket?

Contact your utility’s metering or new-service department directly, or have your electrician confirm the requirement as part of the permit process; this varies by utility and sometimes by specific program, such as solar interconnection or demand-response participation. Don’t assume based on a neighbor’s setup, since requirements can differ even within the same utility territory.

What’s the difference between ringless and ring-type meter sockets?

A ring-type socket uses a separate sealing ring that clamps over the meter to the socket, visibly sealed by the utility, while a ringless design integrates the cover differently and doesn’t use that ring. The two are not interchangeable, and the choice is dictated by your utility’s standard, not personal preference.

Is a meter-main combo unit better than a separate meter socket and panel?

It depends on the installation; a combo unit can simplify a single-enclosure setup for some service upgrades, but local code may require specific disconnect placement relative to the meter that affects whether a combo unit fits the job. Your electrician can advise based on your specific panel location and code requirements.

What happens if I install the wrong jaw configuration?

The utility will typically refuse to energize the service or will require the socket to be replaced with the correct configuration before connecting power, resulting in extra cost and delay. This is why confirming the required configuration with the utility before purchase is the single most important step in this process.

Does the meter socket need to be rated for outdoor use?

Most residential meter sockets are mounted outdoors and need a rainproof or outdoor-rated enclosure as stated by the manufacturer and required by code for that installation type. Confirm the enclosure’s environmental rating matches your mounting location before installation.

K
Kocoda Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.