Key takeaways
- Soft (annealed) copper tubing in a 100 foot coil suits HVAC refrigerant lines and runs that need bending around corners, while rigid (hard-drawn) copper…
Soft (annealed) copper tubing in a 100 foot coil suits HVAC refrigerant lines and runs that need bending around corners, while rigid (hard-drawn) copper tubing suits exposed plumbing runs where a straight, professional appearance matters, and the right choice depends mainly on tube type, wall thickness, and what the tubing will carry. This guide covers the common 100 foot copper tubing types, their typical uses, and what to check before buying.
Soft Copper vs Rigid Copper Tubing
Soft copper, often called annealed or refrigeration-grade tubing, is sold in coils because it has been heat-treated to stay flexible, allowing it to be bent by hand or with a tubing bender around tight corners without specialized joints. This makes it the standard choice for HVAC refrigerant lines, mini-split installations, and other runs where avoiding extra fittings reduces potential leak points. Rigid copper tubing comes in straight lengths rather than 100 foot coils for the most part, so when a listing specifically advertises 100 feet, it is almost always the soft, coiled type intended for flexible routing.
Type K, L, and M Copper Tubing
Copper tubing is classified by wall thickness under ASTM standards: Type K has the thickest wall and is commonly used for underground or high-pressure applications; Type L has a medium wall thickness and is widely used for general plumbing and HVAC; Type M has the thinnest wall and is typically reserved for low-pressure applications where local code permits it. Refrigeration-grade copper (sometimes called ACR tubing) is sized and cleaned specifically for air conditioning and refrigeration systems and is usually what’s sold in 100 foot coils for HVAC work, distinct from the K/L/M classifications used in general plumbing.
Local plumbing and mechanical codes often specify which type is required for a given application, so checking local code requirements before buying is more reliable than assuming any copper tubing will satisfy an inspector.
Diameter and Application Matching
Common diameters sold in 100 foot coils range from small refrigerant-line sizes around 1/4 inch up through 3/4 inch or larger, and the correct diameter depends entirely on the system being installed — HVAC manufacturers specify required liquid and suction line sizes for a given unit’s capacity, while plumbing runs are sized based on fixture demand and local code. Using an undersized line can restrict flow and strain a system, while an oversized line adds unnecessary cost and can affect refrigerant charge calculations on HVAC systems, so matching the manufacturer’s specified diameter is important rather than estimating.
Refrigerant-Grade vs General Purpose Copper
Refrigeration-grade (ACR) copper tubing is cleaned and capped at the factory to keep the interior free of oxidation and debris, which matters for HVAC systems where contamination can damage compressors. General-purpose copper tubing sold for plumbing is not held to the same internal cleanliness standard, so using plumbing-grade tubing on a refrigerant line is generally discouraged by HVAC manufacturers and installation guides. Buyers should check the product listing specifically states ACR or refrigeration-grade if the tubing is intended for an air conditioning or heat pump line set.
At a Glance Comparison
| Type | Best For | Key Stated Specs | Limits |
|---|---|---|---|
| Soft ACR refrigeration-grade coil, 100 ft | HVAC line sets, mini-splits, refrigerant runs | Flexible, factory-cleaned and capped, sized per maker for line-set diameters | Not intended for drinking water plumbing per most guidance |
| Soft Type L general-purpose coil, 100 ft | General plumbing runs needing bends without extra fittings | Medium wall thickness, bendable per maker | May not meet ACR cleanliness standard for refrigerant use |
| Soft Type K coil, 100 ft | Underground or higher-pressure plumbing runs | Thickest wall among common types per ASTM classification | Heavier and costlier per foot than thinner-wall types |
| Small-diameter refrigerant line coil (around 1/4-3/8 in), 100 ft | Mini-split and small HVAC system installs | Sized for typical suction/liquid line specs per maker | Not suited to larger-capacity HVAC systems needing wider lines |
| Larger-diameter coil (1/2-3/4 in), 100 ft | Larger HVAC systems or higher-flow plumbing runs | Wider bore for higher capacity per maker | Harder to hand-bend tightly than smaller diameters |
Pick This If…
| Situation | Recommended Pick |
|---|---|
| You’re installing or extending an AC or mini-split refrigerant line | Soft ACR refrigeration-grade coil, 100 ft |
| You need a general plumbing run with some bends | Soft Type L general-purpose coil, 100 ft |
| Your run is underground or local code requires a thicker wall | Soft Type K coil, 100 ft |
| Your HVAC system’s manual specifies a small line diameter | Small-diameter refrigerant line coil (around 1/4-3/8 in), 100 ft |
| Your system or plumbing demand calls for a wider bore | Larger-diameter coil (1/2-3/4 in), 100 ft |
Fit and Compatibility Notes
Before buying, confirm the exact outer diameter required by the HVAC unit’s installation manual or by local plumbing code, since copper tubing is typically specified by nominal size that can cause confusion between actual outer and inner dimensions depending on type. Fittings, flare nuts, and connectors must match both the tubing diameter and type (flare fittings suited to soft copper, sweat/solder fittings common to both soft and rigid copper), so buyers should plan fitting purchases alongside the tubing itself rather than assuming universal compatibility. Anyone working with refrigerant lines should also be aware that handling refrigerant itself is regulated and typically requires appropriate certification, separate from simply purchasing and routing the tubing.
Alternatives Worth Considering
- Insulated line set kits: Pre-paired refrigerant lines with factory-applied insulation, convenient for straightforward mini-split installs where custom bending isn’t needed.
- PEX tubing for general plumbing: A flexible, often lower-cost alternative to copper for water supply lines where local code permits, though it is not a substitute for refrigerant applications.
- Rigid straight-length copper pipe: Better suited to exposed, straight plumbing runs where a traditional soldered-joint appearance is preferred over a coiled, bent installation.
Frequently Asked Questions
What is the difference between ACR copper tubing and regular plumbing copper?
ACR (air conditioning and refrigeration) tubing is cleaned and sealed at the factory to prevent internal oxidation and contamination, which protects sensitive HVAC components like compressors. Regular plumbing-grade copper is not held to this same internal cleanliness standard. HVAC manufacturers generally specify ACR-grade tubing for refrigerant lines rather than general-purpose copper.
Can I use Type M copper tubing for HVAC refrigerant lines?
Type M is a general plumbing classification based on wall thickness and is not the same as refrigeration-grade (ACR) tubing, which is defined by factory cleanliness and sealing rather than the K/L/M wall-thickness system. HVAC installation manuals typically call for ACR-rated tubing specifically. Checking the manufacturer’s installation requirements is the reliable way to confirm compatibility.
How do I know what diameter copper tubing my mini-split needs?
The mini-split or HVAC unit’s installation manual specifies required liquid and suction line diameters based on the system’s capacity and the length of the run. Using a diameter other than what’s specified can affect system performance and refrigerant charge. Checking this manual figure is more reliable than estimating from the unit’s general size.
Is soft copper tubing as durable as rigid copper?
Soft copper is more flexible by design, which comes from the annealing process, but this does not necessarily mean it’s less durable for its intended use — HVAC and refrigeration systems rely on soft copper’s flexibility precisely because it reduces the number of joints needed. Rigid copper suits applications where straight runs and traditional soldered joints are preferred. Neither type is a direct substitute for the other’s intended application.
Do I need a license to work with refrigerant lines myself?
Purchasing and routing copper tubing itself is generally not regulated, but handling refrigerant — charging, recovering, or evacuating a system — typically requires certification in many regions due to environmental and safety regulations. Buyers planning a full HVAC installation involving refrigerant handling should check local requirements or consult a licensed HVAC technician. Local code and environmental regulations vary by region.
What fittings work with 100 ft soft copper coils?
Soft copper is commonly paired with flare fittings, which don’t require soldering and suit field installations, as well as standard sweat/solder fittings. The correct fitting type depends on the installation method being used and the tubing’s exact outer diameter. Matching fitting size precisely to the tubing diameter is necessary to avoid leaks at the joint.
Related guides